Бюллетени по техобслуживанию могут быть представлены Покупателям на русском языке.

Technical Service Bulletins

If you have additional service questions, please call us at 800.968.0444 or 989.354.4111.  If you have general technical service questions, not of an urgent matter, you can e-mail our Technical Service Department.

After Hours
If you are in the United States and have an emergency situation after hours, Besser staff can be contacted through a pager system. Leave your area code and phone number, and a Besser representative will return your call quickly.

Block Machines

89-3	Vibrator motor sheaves for block machines
91-1	Improved pneumatic control system for Bescodyne vibrators
91-2	How the Trabon Air Grease Pump Works
92-2	Adjusting second stop on Besser cam operated machines
93-4	The Bescodyne drive service tip
93-5	Agitator encoder set-points
94-2	Extending life of Bescodyne units
94-3	Update Bescodyne Clutch/Brake units from single to double air flow valve
95-1	Check the Bescodyne Clutch/Brake stacks for wear
95-2	Gemco cam limit switch boxes (Supercedes SB-No. 90-6)
95-3	Modify Air Compaction Device air cylinders to reduce rod wear
95-4	Instruction to move electrical box to left hand side of vibrator motor
95-5	Using the Encoder for Allen-Bradley PLC®-2Progammable logic controller
95-7	New style crossport and singling plate
96-5	V3-12 Pinion shaft assembly (Besser No. 464229) installation w/locking assembly
97-1	Using the Encoder for Allen-Bradley SLC™-500 programmable logic controllers
97-4	Updated adjustments for 5-5/8" high units on a V-4 or V-4 (26"deep machine)
97-5	Recommendations for use of Vibrator weights
98-2	AFC SmartPac® Operating Instructions (Supercedes SB-No. 95-6 and SB-No. 96-1)
00-1	Installation of KAMCO box (to replace GEMCO box)
00-2 Rev 1	Bull and Pinion Gear Clearance and Alignment Procedure for MK3 Style Pinion Shafts - REVISED JANUARY 2002
01-1	Improved Vibrator Bolts
01-2	Bull Gear and Pinion Indexing and Replacement Recommendations
02-1	Pallet Lug Link Pins

Back to Top

Cubers

89-2	Quick reference guide for ordering AF-7 wear plates
89-5	SF-7 and SF-7W Cuber slider plate drive sprocket and wear bar adjustments
89-6	Wire mesh belt installation and adjustment instructions

Back to Top

Electrical

90-4	T-30 plant floor terminal set-up information
92-1	Putting Allen-Bradley SLC™-150 controllers back in the RUN MODE
93-2	Besser NEMA and current transformer type
94-1	Xycom 2050 Graphics display unit set-up information
95-2	Gemco cam limit switch boxes (Supercedes SB-No. 90-6)
97-3	SLC™-500 programmable controller
98-1	Xycom 2050 Graphics Display Unit set-up information for use with a PLC®
99-2	Installing Screen Program in PanelView™ 900/1000 with a Flash Card
00-1	Installation of KAMCO box (to replace GEMCO box)
00-5	Open Rotor Test

Back to Top

Hydraulic

90-5	Hydraulic tank liquid level switches
97-2	Achieving peak hydraulic system efficiency

Back to Top

Mixers

89-1	6, 9 and 10 yard slump mixer air/grease purged dust hubs
90-1	New mixer blade sets of parts and installation procedure
99-1	Breather Vent and Split Oil Seal
02-2	New Mixer Blade Sets of Parts and Installation Procedure Using Epoxy

Back to Top

Molds

90-3	Quick reference guide for ordering agitator grids
93-1	Quick order reference quide for mold pallet guides  (Supercedes SB-No. 90-2)
96-2	Mold compartment dimensions
96-3	Descriptions and examples of how to order mold parts
96-4	Besser Mold assembly and torque requirements
97-5	Recommendations for use of Vibrator weights
97-6	Portable Mold Jig
98-2	AFC SmartPac® Operating Instructions  (Supercedes SB-No. 95-6 and SB-No. 96-1)

Back to Top

Multi-Spade Besser-Matic

93-3	Dip switch adjustments - Warner CBC-300 adjustable brake control
00-3	Besser-Matic® 1305 Frequency Drive Programming Instructions
00-4	Procedure to Align Carriage and Ball Screw

Back to Top

Rack Transporters

91-3

LSC-40 rotating cable anchor

Back to Top

Skip Loaders

89-4

Boston gear 700 series reducer lubrication

Back to Top